Bathroom remodeling
Kitchen remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Bathroom Remodeling: The Miami Gardens Owner’s Guide
Schluter bathroom remodeling in Miami Gardens runs $10,620 to $33,040 installed, depending on shower size, tile selection, and how much of the existing subfloor and framing can be reused. Nobody remodels a bathroom same-day, and we won’t tell you otherwise – a bonded waterproofing system needs a properly cured assembly before a single tile goes down. What you get from us is a written, line-item scope, permits pulled on every eligible job, and inspections signed before we close the wall.
The part that usually starts the phone call isn’t the tile. It’s the flange. Schluter’s KERDI-DRAIN and KERDI-LINE systems rely on a two-stage seal at the drain body, and when a Miami Gardens install was done with a mismatched strainer frame or a riser cut short, you find out years later – a ring of dark grout that never dries, a musty smell after a shower, or thinset crumbling around the drain ring. In this city we also see the failure show up in shower benches and curbless transitions, where the waterproofing membrane was lapped wrong and water found the one seam that wasn’t banded.
Which Schluter Models This Applies To
Schluter is a German waterproofing and tile system, not a fixture brand, so “which model” means which of its product lines was specified on your job. The common ones in Miami Gardens bathrooms:
- KERDI-DRAIN – the standard central drain with a square or round grate and a bonded flange. Grates come in multiple sizes (typically 4-inch and 5-inch frames) and in matte black, brushed stainless, and oil-rubbed finishes. The grate size and finish are what people get wrong when ordering a replacement.
- KERDI-LINE – the linear drain, 28-inch to 72-inch channel lengths. Length and outlet position (center vs. offset) are not interchangeable, so measure the channel and count the grate segments before you call anyone.
- KERDI-SHOWER systems – the pre-sloped tray, curb, and bench kit that ties into the drain above. The tray is sized to your shower footprint; a tray that doesn’t match means a custom mud bed, which changes the labor line.
- DITRA and DITRA-HEAT – the uncoupling membrane under floor tile, and the electric heat mat some owners add. DITRA-HEAT mat widths are fixed, and a failed sensor in the mat is a real repair, not a reset.
- DILEX and KERDI-BAND – movement joints and seam banding. Cheap parts, critical function, and the ones most often skipped by a crew cutting corners.
To identify the right part, read the grate frame (it’s stamped), measure the drain opening across the flats, and pull the original spec sheet if the previous owner kept the paperwork. When you can’t find it, the honest answer is a site visit – we won’t guess at a part number over the phone for a drain that costs real money to reorder.
OEM vs. aftermarket: on Schluter specifically, the seal is the whole point. A no-name grate frame that’s “close” will not seat the way the original does, and the leak comes back. We install Schluter parts and we’ll tell you plainly when an aftermarket equivalent is a false economy.
Barrett & Sons Construction Miami Gardens is an independent service provider – we’re not affiliated with Schluter, we install and repair its systems.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Bathroom Remodeling Is Failing
- Grout around the drain stays dark for days after a shower. That’s moisture sitting under the tile because the drain seal isn’t doing its job – usually a missing KERDI-BAND ring or a flange that was never bonded to the membrane. A properly built Schluter drain dries out overnight.
- A musty smell that comes back a week after you clean. In South Florida’s year-round humidity, a hidden leak doesn’t dry out the way it would in a dry climate. It feeds mold in the wall cavity behind the cement board, and you smell it long before you see it.
- Loose or hollow-sounding tile around the shower perimeter or curb. That’s a failed bond, often from a pre-sloped tray that wasn’t set level. Water pools, the thinset shears, and the tile lifts. Hollow sound under a tap is the tell.
- Water staining on the ceiling below, or a soft spot in the hallway floor. This is the failure that already found the subfloor. In Miami Gardens’ rainy season, a slow perimeter leak travels fast and shows up as a brown ring on the drywall ceiling of the room underneath.
- Cracking along the shower bench or the curbless transition. Movement joints (DILEX) were skipped, or the framing flexed before the membrane was installed. Tile cracks at the weakest point, and it’s almost always a corner or a bench seam.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For Miami Gardens, here’s how the numbers break down for a Schluter-system bathroom:
| Scope | Installed range |
|---|---|
| Bathroom remodel (full Schluter system, tile, fixtures) | $10,620 – $33,040 |
| Small bathroom remodel | $5,900 – $14,160 |
| Walk-in shower installation (KERDI-SHOWER, linear drain) | $5,310 – $14,160 |
| Tub-to-shower conversion | $4,130 – $11,800 |
| Shower replacement | $3,540 – $10,030 |
| Bathroom vanity installation | $945 – $3,540 |
What drives the range: whether the existing subfloor and framing are sound, tile choice (large-format porcelain in a small bath costs more in labor than 12×12 sheet), whether a linear drain needs to relocate, and whether the shower was previously set on a pre-sloped tray or a custom mud bed. A standard drain swap in an existing Schluter shower is the low end. A full rebuild with a relocated linear drain and new tile is the high end.
Parts and labor are line-itemed. You see the drain cost, the membrane cost, the banding, the tile, the labor, and the permit. No hidden allowance. Every price change gets a written change order before we touch the wall – the Barrett & Sons rule is simple: an allowance that isn’t on paper is a surprise waiting for a date. Every eligible job comes with permits pulled and inspections signed, and a written 90-Day Done Right Promise on the work.
DIY or Call Us?
An owner can safely do some checking first: confirm the grate finish and size, look for the stamped part number, and watch the drain area for a day after a shower to see whether it dries out. That much is fair game.
What we don’t recommend is pulling the drain and re-bedding the membrane yourself. A Schluter shower is a bonded waterproofing system – the membrane, the drain flange, and the banding have to be lapped in a specific order with the right thinset. Get that order wrong, and you don’t get a slow leak; you get a hidden one that keeps feeding the wall cavity for years. We’ve seen it in Miami Gardens bathrooms more than once: a homeowner who saved $400 on the drain and spent $6,000 on water damage a season later. Our technicians have up to 28 years of experience, and we’d rather spend an hour on the phone than have you live with that. Call (844) 797-8316 and we’ll talk through what you’re seeing before you commit to anything.
FAQs
A properly installed one should last 25 to 40 years – the membrane itself is rated for decades, and the failure point is almost always the install, not the material. In Miami Gardens’ humidity, that lifespan depends on ventilation (a working exhaust fan matters more than most owners realize) and on whether the drain seal was done right the first time. Call (844) 797-8316 for an honest read on yours.
Often yes, if the failure is confined to the drain grate, a band, or a single movement joint. A full replacement is the answer when the subfloor is wet or the membrane bond has failed across the pan. We’ll tell you which one you’re looking at after a site visit, not before.
A drain or grate replacement in a sound shower takes one to two days plus tile cure. A shower replacement runs three to five days for the tear-out, system install, and tile, and a full bathroom remodel is two to three weeks depending on scope. We don’t quote same-day on planned construction – that’s not how a waterproofing system works.
We order Schluter components directly, matched to your measured drain body, grate size, and outlet position, with lead times confirmed before we schedule. We don’t carry parts on a truck, and we don’t guess at a part number – if we can’t verify it against your existing system, we measure first.
We also install KraftMaid and Cambria in kitchens, and Silestone counters, so if your remodel touches more than one room, one written scope handles it.
If you’ve got a Schluter bathroom that isn’t drying out, or you’re ready to plan a remodel in Miami Gardens, call (844) 797-8316 for a free estimate. No trip charge inside the county, a free second opinion on any written estimate, and a live person answers the phone around the clock. Our technicians have up to 28 years of experience, and every eligible job gets permits pulled, inspections signed, and the written 90-Day Done Right Promise.
Written by the team at Barrett & Sons Construction Miami Gardens, serving Miami Gardens and nearby areas.